Every ESP32-P4 board

The ESP32-P4 boards I have looked at, and whether ESP-KVM runs on them. Supported boards are in the catalog, rated for a KVM out of five; the others say what is missing.

What a board needs

  • 32 MB of PSRAM. Capture, the encoder and TLS do not fit in 16 MB. On the chip it reads NRW32 (rev 1.x) or NRW32X (rev 3.x); NRW16 boards do not qualify.
  • A free camera connector. The HDMI capture board plugs into the P4's MIPI-CSI: a Raspberry Pi style 15-pin or 22-pin ribbon. A camera soldered onto that connector, or a board-to-board plug, takes it away.
  • The P4's high-speed USB on a connector it can drive as a device. That port is the keyboard and mouse the target sees. Behind a hub, or not brought out at all, it cannot be.
  • A network. An Ethernet PHY on the board, or an ESP32-C6, C5 or C61 for Wi-Fi.

Have a board that is not supported yet?

If it is a candidate or a maybe below, or not in the list at all, one request is enough: I add a board as soon as someone who has it can try a test build.

  1. Open a board request in Discussions. The form asks for the board's shop page, its schematic if there is a link, the chip marking and the capture board you have.
  2. I make a test image from the schematic and post it in the thread.
  3. You flash it on the flasher with Install another version from a file, and tell me what works. The flasher's Back up the flash keeps the board's old firmware.
  4. Once the picture, the keyboard and the network work, the board goes into the catalog with its own image and updates.

ESP32-P4 boards for ESP-KVM

Green has it, orange does not, no colour is not known yet. The four columns are the four needs above. For the camera, what counts is whether the capture board's Raspberry Pi ribbon fits: a 15-pin or 22-pin connector in Pi order. A connector of another kind, or with an unpublished pinout, stays unknown.

BoardESP-KVMPSRAMCamera ribbonUSBNetworkChip revNotes
Waveshare ESP32-P4-ETHSupported✓22-pin, Pi 5 kind✓✓1.x, 3.x100M Ethernet, PoE with an add-on module (in the ESP32-P4-POE-ETH kits)
Espressif ESP32-P4 Function EV BoardSupported✓15-pin, Pi order✓✓1.x, 3.x100M Ethernet, Wi-Fi 6 (ESP32-C6)
Waveshare ESP32-P4-NANOSupported✓15-pin, Pi order✓✓1.x, 3.x100M Ethernet, PoE with the add-on PoE module (in kits B, C and D), Wi-Fi 6 (ESP32-C6)
Guition ESP32-P4-M3-DevSupported✓works with the C790✓✓1.x, 3.x100M Ethernet, Wi-Fi 6 (ESP32-C6)
Waveshare ESP32-P4-WIFI6-POE-ETHSupported✓15-pin, Pi order✓✓1.x, 3.x100M Ethernet with PoE, Wi-Fi 6 (ESP32-C6)
Waveshare ESP32-P4-WIFI6Supported✓15-pin, Pi order✓✓1.x, 3.xWi-Fi 6 (ESP32-C6) only
Waveshare ESP32-P4-WIFI6-DEV-KITSupported✓15-pin, Pi order✓✓1.x, 3.x100M Ethernet, PoE with an add-on module (not in the kits), Wi-Fi 6 (ESP32-C6)
DFRobot FireBeetle 2 ESP32-P4Supported✓15-pin, Pi order✓✓1.xWi-Fi 6 (ESP32-C6) only
M5Stack Unit PoE-P4Supported✓24-pin, M5Stack add-on only✓✓1.x100M Ethernet, 802.3at PoE
Waveshare ESP32-P4-Module-DEV-KITSupported✓15-pin, Pi order✓✓1.x, 3.x100M Ethernet, PoE with an add-on module (not included), Wi-Fi 6 (ESP32-C6)
Waveshare ESP32-P4-NANO-WIFI6-DBSupported✓15-pin, Pi order✓✓3.x100M Ethernet, PoE with the add-on PoE module (in kits B, C and D), dual-band Wi-Fi 6 (ESP32-C5)
Waveshare ESP32-P4-WIFI6-DBSupported✓22-pin, Pi 5 kind✓✓3.xdual-band Wi-Fi 6 (ESP32-C5) only
JetKVM MiniSupported✓?✓✓3.x100M Ethernet
Espressif ESP32-P4X-C5-Function-EV-BoardSupported not run on one yet✓15-pin, Pi order✓✓3.x100M Ethernet, dual-band Wi-Fi 6 (ESP32-C5)
VIEWE ESP32-P4-PiSupported not run on one yet✓15-pin, Pi order✓✓1.x100M Ethernet, Wi-Fi 6 (ESP32-C6)
M5Stack Unit PoE-P4XSupported not run on one yet✓24-pin, M5Stack add-on only✓✓3.x100M Ethernet, 802.3at PoE
JetKVM Mini WSupported not run on one yet✓?✓✓3.xWi-Fi 6 on 2.4 and 5 GHz (ESP32-C5)
OspreyPi / Maker Go ESP32-P4-Mini v2.0Maybe✓likely a camera-module pinout?✓1.xA C6, microSD, a Type-C labelled high-speed USB. The camera connector looks wired for a camera module (its own 2.8 V and 1.8 V supplies), not in Pi order. (source, checked 2026-10)
Guition JC1060P470 (7", Ethernet version)No✓15-pin 0.3 mm✓✓?Built on the JC-ESP32P4-M3 module, the same as the supported Guition ESP32-P4-M3-Dev, with IP101 Ethernet, a C6 and a high-speed USB-C. But its camera socket is 15-pin at 0.3 mm pitch, so a Raspberry Pi ribbon does not fit without an adapter. (checked 2026-11)
Olimex ESP32-P4-PCNo✓15-pin, Pi order✗✓?Everything else is right, but a USB hub sits on the high-speed port, so it is always a host and can never be the target's keyboard. (checked 2026-09)
Olimex ESP32-P4-DevKitNo✓15-pin, Pi order✗✓?The high-speed USB lines are not brought out anywhere; its Type-C is the serial bridge. (checked 2026-09)
Spotpear ESP32-P4-MINI-A with ESP32-P4-EXTNo✓22-pin on the EXT board✗✓1.xA tiny core module and a plug-on board with a C6, a 22-pin camera socket and four USB-C ports. Those four ports hang off a CH334F hub on the high-speed USB, so it is always a host and can never be the target's keyboard. The core's own USB-C is the serial and JTAG port. No Ethernet and no microSD slot. (source, checked 2026-11)
Waveshare ESP32-P4-Pico, ESP32-P4-Core-DEV-KITNo✓22-pin on the Core kit?✗?No network at all: no Ethernet PHY and no Wi-Fi co-processor. (checked 2026-09)
Waveshare ESP32-P4-86-Panel-ETH-2RONo?not fitted?✓?The camera connector is not fitted on this variant. (checked 2026-09)
LILYGO T-Display-P4No?built-in camera???The camera is built in; there is no free camera connector. (checked 2026-09)
Seeed reTerminal D1001No✓built-in camera?✓1.xThe camera is built in; there is no free camera connector. A good terminal candidate, below. (source, checked 2026-10)
Espressif ESP32-P4-EYE, ESP32-P4X-EYENo?built-in camera???Camera kits: the camera connector carries their own sensor. (checked 2026-09)
M5Stack Tab5As a terminal✓built-in camera?✓1.xNot as a KVM: the camera connector holds its own camera. It runs ESP-KVM terminal instead, as a handheld screen for a KVM. (checked 2026-10)
LILYGO T-Halow P4No✗24-pin, no 3.3 V, 1.8 V I2C✗✓?8 MB of PSRAM. USB and Ethernet come out only on the M.2 edge, with no PHY and no socket for the target, and the 24-pin camera connector has no 3.3 V and a 1.8 V I2C. (checked 2026-09)
Adafruit Metro ESP32-P4 HydraNo✗22-pin, Pi format?✓1.x16 MB of PSRAM and a rev 1.x chip. The high-speed USB comes out on a Type-A host port with its own 5 V supply, the Type-C is full speed. A C6 for Wi-Fi, no Ethernet. No schematic yet. (source, checked 2026-10)
Elecrow CrowPanel Advanced 5inch ESP32-P4 HMI AI DisplayNo✓24-pin, Elecrow's own✓✓1.xESP32-P4NRW32 (rev 1.x), a C6 on SDIO and the high-speed USB on its own connector. But the camera socket is 24-pin for its own camera, at 2.8 and 1.8 V with I2C at 1.8 V, so a Raspberry Pi ribbon does not fit. (source, checked 2026-11)
Makerfabs MaTouch ESP32-P4 TFT with Touch 7"No✓24-pin, for Makerfabs' SC2336 camera✓✓1.xA C6, high-speed USB on its own USB-C, Ethernet on the 10.1". But the camera socket is 24-pin for the SC2336 camera, at 2.8 and 1.8 V, so a Raspberry Pi ribbon does not fit. (source, checked 2026-11)
M5Stack Stamp-P4No✓16-pin board-to-board, needs an adapter✓✓1.xHigh-speed USB on edge pads and Wi-Fi with the C6 add-on. But the camera is on a 16-pin board-to-board connector, so a Raspberry Pi ribbon does not fit without an adapter. (source, checked 2026-11)
Osprey OspreyPi-P4C5-ModuleCandidate✓15-pin 1.0 mm, Pi pinout (per the maker)✓✓?An ESP32-P4 core board with a dual-band ESP32-C5, a Raspberry Pi style camera connector and high-speed USB on a Type-C or Type-A socket. (checked 2026-11) Have one? Request it →
RELOC SCINTIX P4Candidate✓on the carrier board (its CSI1 / CAM1 connector)✓✓3.xAn ESP32-P4 compute module in the Raspberry Pi CM4/CM5 form factor, with Ethernet and an ESP32-C6, that plugs into CM4 and CM5 carrier boards. (checked 2026-11) Have one? Request it →
Waveshare ESP32-P4-WIFI6-Touch-LCD-7BCandidate✓15-pin, Pi order✓✓3.xA 7" MIPI-DSI touch display board with an ESP32-C6, a Raspberry Pi camera connector and a USB-A socket on the P4's high-speed USB. (checked 2026-11) Have one? Request it →
Wireless-Tag WT32P4C5-43SCandidate✓15-pin, Pi order✓✓3.xA 4.3" touch screen in a case, with an ESP32-P4 and an ESP32-C5 for Wi-Fi on the board behind it. (checked 2026-11) Have one? Request it →
Wireless-Tag WT99P461-S1Candidate✓15-pin, Pi order✓✓3.xA large ESP32-P4 development board with Ethernet, an ESP32-C61 for Wi-Fi, RS-485 and CAN. (checked 2026-11) Have one? Request it →
Wireless-Tag WT99P4C5-S1Candidate✓22-pin, Pi order✓✓?A large ESP32-P4 development board with Ethernet, an ESP32-C5 for Wi-Fi, RS-485 and audio. (checked 2026-11) Have one? Request it →
Wireless-Tag WTDKP4C5-S1Candidate✓22-pin, Pi order✓✓?A small ESP32-P4 development board on the WT01P4C5-S1 module, which has an ESP32-C5 for dual-band Wi-Fi. (checked 2026-11) Have one? Request it →
Wireless-Tag WT9932P4C61-TINYMaybe✓15-pin, Pi order✓?3.xA narrow 33 x 69 mm ESP32-P4 board with an ESP32-C61 for Wi-Fi, made to sit in a breadboard. (checked 2026-11)

Boards for ESP-KVM terminal

ESP-KVM terminal is the other end: a board with a screen that shows a KVM's picture, with no browser. It needs a screen with touch and a network, but no camera connector and no USB to a target. Today it is written for the Tab5 only.

BoardTerminalScreenNetworkBatteryNotes
M5Stack Tab5Supported5", 1280x720Wi-Fi (C6)✓What the terminal is built and tested on. The Keyboard for Tab5 clips on.
Espressif ESP32-P4 Function EV BoardCandidate7", 1024x600Ethernet, Wi-Fi (C6)✗It already runs ESP-KVM, so one board could be both ends.
Guition ESP32-P4-M3-DevNot ported4.3"Ethernet, Wi-Fi (C6)?The same board also runs ESP-KVM itself.
Seeed reTerminal D1001Not ported8", 800x1280Wi-Fi (C6)✓32 MB PSRAM and a 2500 mAh battery. The closest to the Tab5 of the lot. (source)
Wireless-Tag WT32P4C5-43SNot ported4.3", 800x480Wi-Fi (C5)? (source)
Waveshare ESP32-P4-WIFI6-Touch-LCD panelsNot portedseveral sizesWi-Fi (C6)?
Elecrow CrowPanel AdvancedNot ported5", 7", 10.1"Wi-Fi (C6)? (source)
Makerfabs MaTouch ESP32-P4Not ported7", 10.1"Wi-Fi (C6); Ethernet on the 10.1"? (source)

Everything but the supported boards is read from schematics and vendor pages, not from hardware. Have one of the candidates, or a P4 board that is not here? Open an issue with a link to its schematic.